Maybe its nothing just me being paranoid. Below is a few pictures I took on a slide after running just 150 rounds of Fiocchi 115 CMJ (from the box “Complete Metal Jacket”)
Compare to the Walmart Federal 9mm aluminum that I used to run, this load seem to kick a bit harder than usual.
After field...
Two part questions
I have a YHM 9mm suppressor, the host is a Kel Tec S2k with factory threaded barrel.
At 25 yrd, with 115 gr 9mm it is consisting shooting 3 in low, and 1 to the right.
I check to make sure the suppressor was tight every mag, and there was no baffle contacts.
Not sure...
I am not even sure if its called mono gas ring, its a single, but continuous gas ring, almost like a key ring that loops around 3 times. This is quite different from the traditional 3 rings.....
A sale associate of Precision Firearms mentioned this design avoid the misalignment of the...
Came across GlockDoc's article: http://www.theglockdoc.com/Glock_Maintenance.html and start to grow concerns.
My gen3 G19 had about 50k rounds in the last 10 yrs without replacing any of the springs and did not show signs of frame wear.
My gen4 G17 had to go through major rebuilt after the...
Just bought 6 box of Walmart Black box American Eagle. I used this ammo for target for years and didn't have any problem. But I opened these box and discovered the following issues. Out of 120 rounds, about 18 are irregular.
Dimple by case neck
Visible difference in bullet seating...
I been thinking about dressing up my Kel Tec sub2000 for a while. After upgrade the rail system to red lion, an idea came though about fitting it with my suppressor. So I made a call to Atlantic Guns and they will thread it for me. Thinking about saving money on labor, I decide to remove the...
Ok, it is me over reacting. I think it is still a very good product its just happen to be my Gen4 G17 is the older-with-no-nose-SOL model. So it could've work just fine on your Gen4. However if your Gen4 is like mine - Older, then you will need to see this.
After 5 long weeks, its finally...
I recently had one of mine 9mm carbine threaded to take surpressor. so naturely I am looking for a thread protector. Since the surpressor will not stay on it all the time, I am thinking just get a flash hidder as thread protector then.
Smith Vortex is my primary choice, since its pattern will...
I place an order using glock's non-armor part list/form for the new G17 Beavertail.
Order were faxed in on 5/27/13 with confirmation, they charged my card on 6/10/13. As today, no words on shipping/tracking number.....
Never order from glock before and I know the beavertail is hot in...
So, here is my not fair comparison for Aliengear (AG) on Glock 17 Gen 4 vs Crossbreed (CB) on XD 9mm sub compact. Not fair because its full size vs sub compact. Hope this will provide you some idea before you make your purchase.
Order placed on 6/4, and geez its here on 6/7.
This got CB beat...
So, I got kicked again because I had "evil features" on my Mossberg 500. Ghost ring sights, barrel too short (22 inches, not 18.5)), and of course, pistol grip... etc.
Its my fault, their house their rules.
Looking for a basic over and under, do not need anything fancy like the gold trim...
I bought a lyman #49 to do my initial reading on learning how to reload.
For 9mm, it seem only supplied load data for 115gr jacket HPs. I plan to start loading 115 FMJ. Would it be ok to use the load data supplied for HP for FMJ since its the same weight?
Another questions for 38...
Ruger LCR 357, purchased used several month back. Great little revolver with awesome trigger. Bought it for pocket carry, and some BUG event fun. Surprisingly accurate for a snubbie, happy happy happy until discover this while cleaning............
I thought it was excess lead build up, soak...
Joeboboutfitters.com has Kies AR 15 bolt on sale for 54.95.
http://www.joeboboutfitters.com/Kies_223_5_56_AR_15_BOLT_No_carrier_p/kies-223-bolt.htm
I have a RRA AR15 and like to keep a spare bolt just in case. RRA is sold out, has anyone tried out Kies bolt? Couldn't find review on this...
Not sure what is the technical name on this type of target, but here is an example:
So the question is
If I need to engage T1, do I go for the head shot or body shot?
Head shot I might miss - penalty for FTN
Body shot I might hit non-threat, or score lower points
what's my point...
In the market for a Circuit Judge, but got confused on the ammo selection, please help me to clear these 2 questions:
1. Circuit Judge is listed for 410 and 45LC, but it will be able to shoot 45 ACP right?
2. It has a rifled barrel, so I need 410 Sabot slugs right? Or it doesn't matter? I...
Sorry guys, I tried to search around for the answer but can't find a firm answer.
I currently using a stock G17 for SSP, but if I polish the internal metal parts, would it be consider as another level??
Hi folks, need to pick your brain for some advice on my next project. I had been planning on this build for quite some time but still can’t come to a good resolution.
Objective: A suppressed 9mm SBR that feeds on Glock mags. Budget 800 to 1k. (Prefer 800 so I can be around 1k including stamp)...
Guys
Picked up a new MP40 the other day, after clean and shot it for the first time and ran into some issue.
Several FTF/fail to go into battery in the first 200 rounds. I think it happened with all 3 mags, (I can be wrong on this, I will have the mags marked next time so I can better ID...
Hello
New to the forum, and hoping to get some advise for you all.
Has anyone has experience with Georgia Arms 147gr HP subsonic loads with their lone wolf barrel?
I have a Glock 23 and like to convert to 9mm to mount my Cobra M2. So Lone Wolf seems to be the best fit right now, price and...