Made a Mag Holder

[Harrys]

I have been carrying my Kimber Micro 9mm Rapide most of the time instead of my K40. I finally made an OWB mag holder for the 9mm and it just look like a multitool holder.

 

[Alphabrew]

Nice!

 

[Seagrave1963]

Very nice. Want to make a couple more (hint)?

 

[MRH]

 

[MeatGrinder]

That's nice. I've used leather cell phone holders for years, but my source is getting out of the business.

 

[vanquish1]

Looks nice. I was wondering if anyone made a OWB holster that had extra leather hanging down at the bottom that looked like a cell phone case.

 

[Harrys]

Looks nice. I was wondering if anyone made a OWB holster that had extra leather hanging down at the bottom that looked like a cell phone case.

I actually made one for a close friend he carries a Bodyguard 380. To keep the shape consistent, I used a pine block cut to match his gun outline. Covered the face with soft leather and used a double belt clip. He had a big belly, so IWB was not good for him. With his shirt untucked it looked just like a cell phone case.

 

[Makanik]

Looks Nice Harrys

 

[John from MD]

I have been carrying my Kimber Micro 9mm Rapide most of the time instead of my K40. I finally made an OWB mag holder for the 9mm and it just look like a multitool holder. View attachment 399800 View attachment 399801 View attachment 399802

Very professional looking.

 

[Harrys]

Very professional looking.

Just a rookie

 

[Michigander08]

I like these:

Snagmag - 1791 Gunleather

The SNAGMAG™ is a custom fit accessory.* The floor plate should sit below the top edge of the SNAGMAG™, Figure 1. This may require you to gently move the top of the SNAGMAG™ outward to fully seat the magazine.*The SNAGMAG™ can also be worn inside the waistband as well as in your back pocket. If […]

1791gunleather.com

 

[John from MD]

I like these:

Snagmag - 1791 Gunleather

The SNAGMAG™ is a custom fit accessory.* The floor plate should sit below the top edge of the SNAGMAG™, Figure 1. This may require you to gently move the top of the SNAGMAG™ outward to fully seat the magazine.*The SNAGMAG™ can also be worn inside the waistband as well as in your back pocket. If […]

1791gunleather.com

I have several of those for single stack and 10 round mags. I keep the 17 rd on my belt as it looks like a knife and I notice the weight less.

 

[Harrys]

Well, a bud was over Saturday and saw my mag holder. He asked if I could make him one like it. He carries a S&W M&P 9 Shield. The mag dropped right in and fit well. The mag holder was made for a 7round mag and after some further testing it also works with my 40-caliber mag. I told him take the one I just made, and I will make another. Here is the one I finished Sunday. The snap is a real Buffalow nickel and I stamped cross 1911 in the front. Basically, what I have gleaned is the mag will accompany both 40 and 9mm mags. I measured them both and there are the exact outside detentions.

 

[Boss94]

Very nice workmanship!!!!

 

[John from MD]

Well, a bud was over Saturday and saw my mag holder. He asked if I could make him one like it. He carries a S&W M&P 9 Shield. The mag dropped right in and fit well. The mag holder was made for a 7round mag and after some further testing it also works with my 40-caliber mag. I told him take the one I just made, and I will make another. Here is the one I finished Sunday. The snap is a real Buffalow nickel and I stamped cross 1911 in the front. Basically, what I have gleaned is the mag will accompany both 40 and 9mm mags. I measured them both and there are the exact outside detentions.
View attachment 400138

Now that is some kind of bling! Nice job.

 

[Harrys]

Now that is some kind of bling! Nice job.

Thanks

 

[Harrys]

Very nice workmanship!!!!

Thanks

 

[Blaster229]

Double as a sheath for a Buck knife folder.