You will fit right in here poopdolla. Welcome.
Just don’t pick up a dollar if you see it on the ground...
You will fit right in here poopdolla. Welcome.
I drive a f150 supercrew with a cap and a jeep Wrangler.
Both of these vehicles are open and easy to see into. All my window are tinted but still can be seen trough if looked hard enough.
If the officer sees a gun case and or ammo boxes he/she could say it gives them probable cause to search the vehicle.
The police force has changed a lot and not for the better. But that is a discussion for another time.
It likely wouldnt. However most times I have been pulled over I am asked "Any guns drugs rocket launchers ect ect ect in the car i need to know about"
How am I supposed to answer that? If i say yes there is a handgun you bet they are going to want to see it. If I refuse most officers arent going to just leave it at that.
Do I respond "there is nothing illegal in the car" to the question "Any firearms/drugs in the car i need to know about? I feel like that answer is basically saying yes I have a firearm but it is legal. Because it is clear that you avoided the actual question.
Idk maybe my experiences with police are not the normal. I havent been stopped since I was younger but whenever I was it was often a problem. I have had my car searched before because i guess i "looked like someone who would do drugs" and they brought a dog out that did a BS hit and they found nothing. My experience is if they want to search your car, they will do it. Period.
I guess my experiences with stops have not been very good so I am inclined to be prepared how to handle any situation.
"That I need to know about". Simple, honest answer: "No, officer". It's never in your interest to answer questions that haven't been asked.
Check out the 5Dtactical jig. All you need is a DeWalt router and a hand drill and you are set.
I just got the easy jig from 80%lowers and now y’all have me wanting a Glock and 1911 jig and lowers!
I have a nice Mikita router. Anyone else have issues with the end mill coming out as it's spinning even after being locked in hard as shit?
Maybe the taper doesn't allow for a solid lock? I thought I screwed up my first lower (it is screweed up) but it's because my end mill bit is loosening it self very quickly. Brand new router and the bit only backs out while milling. It's cause a portion to be lower in depth than others (totally fixable at this point) but I don't want to continue because anytime the mill bit hits metal it loosens. It's driving me up a wall
I had the same problem with the Mikita router. Got the Dewalt and haven't had a single problem.
I have a Mikata finish router. The only time the bit backed out was when I tried too much cut, I think. I use the 80% mill bit and tend to take shallower cuts. I torque the bejesus out of the collet.
Also, is the speed of the bit correct? Comes down to feed rate which is related to bit speed, or some such. I turned up the RPMs on the router and the bit started cutting like butter.
Is there any instruction with the jig as to RPM settings?
Sent from my SM-G955U using Tapatalk
lol I can't F'n win. Between Home Depot morons and my own failures this is a mess.
Ha! I even tried tightening the Mikita before each pass and it STILL slipped. Drove me nuts. Take it back. The Dewalt is $15 more.
Yes, that's the best for these jigs. Right between 5/6 is the perfect speed (~25,000rpm IIRC).The DP611?
Wife just printed the return label from Amazon. I'll box it up tomorrroww after work and take it to the store.
Yes, that's the best for these jigs. Right between 5/6 is the perfect speed (~25,000rpm IIRC).
Yes, that's the best for these jigs. Right between 5/6 is the perfect speed (~25,000rpm IIRC).
Ha! I even tried tightening the Mikita before each pass and it STILL slipped. Drove me nuts. Take it back. The Dewalt is $15 more.
I always found finishing one of these to be quite satisfying, but none so more as the Polymer80 Glock clone.When the doc tells you to do something.....you do it!
Dewalt made my life easy