Powder (Range) Container

The #1 community for Gun Owners of the Northeast

Member Benefits:

  • No ad networks!
  • Discuss all aspects of firearm ownership
  • Discuss anti-gun legislation
  • Buy, sell, and trade in the classified section
  • Chat with Local gun shops, ranges, trainers & other businesses
  • Discover free outdoor shooting areas
  • View up to date on firearm-related events
  • Share photos & video with other members
  • ...and so much more!
  • DennisCA

    Active Member
    I got this idea from where but for the life of me I can not remember where but I digress; I wanted something to hold the powder and that was pre-measured.
    Here what I came up with:
    1st the box:
    6xa2.jpg

    [Next the inside:
    cd3o.jpg

    Comparison Pic:
    v1aw.jpg

    The box is a old disc box that I had in my office, the foam padding I also found in my office as well. The plastic containers I got off of ebay for $8.50
    for 25 w/caps (and free shipping!)

    I can have the powder pre-measured and ready to go just before I go to the range - no muss no fuss.
    (prob not a good idea for long-term storage)

    I figure that 25 shots is a good start, so what do you think?
     

    John from MD

    American Patriot
    MDS Supporter
    May 12, 2005
    22,965
    Socialist State of Maryland
    The only thing that I would question is whether you can generate static electricity when pulling the plastic tube out of the foam. I have used plastic and rubber tubes to load before but I always had them loose in a metal ammo can.

    It looks like a neat idea though.

    Regards,

    John
     

    Threeband

    The M1 Does My Talking
    Dec 30, 2006
    25,338
    Carroll County
    This is a very good way to carry your cap-and-ball ammo. Fast, convenient, and safer then loading from a flask.


    We had a discussion about this very technique not long ago.


    If you really want faster reloads get some small plastic screw/snap top tubes and measure out a few dozen charges to carry with you or try rolling paper cartridges....


    I used to use loading tubes like these Quick Loads from Dixie:

    http://www.dixiegunworks.com/advanced_search_result.php?s=1&keywords=+quick+load

    They're squishy, sort of rubbery tubes, closed at one end. I'd throw a powder charge from my flask into each tube, then "cork" the tube with a round ball. I'd load up a bunch at home.

    In use, I'd pop the ball out of a tube and set it aside, then pour the powder charge into a chamber. Repeat for all chambers, then seat the balls.

    It's actually less efficient than the little plastic tubes with hinged plastic caps, if you can find them. Those you just pop the cap with your thumb: no screwing around setting the balls aside, then picking them up again to seat them. But I don't know where to find the snap-top tubes, and these Dixie Quick Loads are almost as good.

    North-South Skirmish Association forbids loading a revolver directly from the flask, so some sort of loading tubes are necessary. The chances of your powder flask turning into a hand grenade (there's that word again!) may be pretty slim, but it's smart to be careful with gunpowder, and these loading tubes really are fast and convenient.

    I am not in any shape or form recommending this seller as it was just a random ebay search but these are the tubes I have previously used as well as screw top tubes.

    You can't actually hold your balls in there...

    http://www.ebay.com/itm/100pcs-2ml-Cylinder-Bottom-Micro-Centrifuge-Tubes-w-Caps-Clear-/390733224929

    IIRC I put 24+ grains in with no problem.


    Those look like very nice tubes. You can hold them in one hand, and pop the top with your thumb. It's really more convenient to just have a separate box or tub or something with a bunch of balls in it. I knew a guy once who could reload in a minute or less that way.

    My Quick Load tubes just use the ball as a cork, and it's a little awkward, because first you fumble with the tube to get the ball out, then you've got to put the ball aside until you're ready for it.

    I still recommend the Dixie tubes. They're very good. But those pop-top tubes are even better.


    I used to carry the loading tubes in plastic MTM cartridge boxes.

    MTM-R50GreenAmmoBox.jpg
     

    Users who are viewing this thread

    Latest posts

    Forum statistics

    Threads
    275,603
    Messages
    7,288,053
    Members
    33,487
    Latest member
    Mikeymike88

    Latest threads

    Top Bottom