Good day MDS,
I'm in need of a contractor or two to do some work, in the Bel air area. My usual contractors are MIA or out of commission. If this isn't the correct location to put this well, i'm sure someone will let me know.
one particularly Big job is:
I have a couple of buildings that need...
G19 for basically all the time
OWB G 17 when a jacket is around
P365 cuz i haven't lost the weight i keep saying i will and i need something for the T-shirts that are too tight
07/06/2022: Final Disposition; Approved.
Permit Restrictions: NONE (MD ONLY) (NOT VALID WHERE FIREARMS ARE PROHIBITED BY LAW)
now just waiting for the postman. Also one of the early no restrictions permits :)
applied 02 May
G&S: TS
Talked to the investigator on 05/26, she was exceedingly friendly. We shall see how it goes moving forward
05/02/2022 10:11 PM APPLICATION HAS BEEN SUBMITTED FOR REVIEW
05/03/2022 01:34 PM APPLICATION HAS BEEN SUBMITTED FOR REVIEW
05/13/2022 03:54 PM APPLICATION HAS BEEN...
I have a need for some carpet install, and potentially some other flooring install in a house i'm renovating. I'm looking to change the wall to wall carpet in a couple rooms in the house. i also have a couple other flooring (tile, vinyl tile) projects that i'll probably do myself but wouldn't...
Last summer, my wife took in five foster cats from a relative who developed some health issues. We currently still have three cats that we are looking to rehome.
This is Penny. She is 9 years old and is a great house cat. She is friendly and sweet, and likes to lay in laps and dog beds...
I would start by trying a new power supply, almost all current power supplies should take the beating and save the rest of the components, if the shock came through the Ethernet, well the router would be dead first. I would assume desktop, but a power supply for a typical computer will run you...
This is a very valid and true statement. this is why they cannot all out ban and confiscate the firearms in this country... it takes decades of slow monotonous restrictions. and after a few generation nobody cares. that is the only way to get to their end goal it must be a little bit at any...
I am looking for some information about fixing and moving a large safe. My MIL has a large safe thats been sitting for a while. It is an old safe with some family history. A few years back some folks decided they were going to break into the safe and steal what was in there. joke's on them, it...
well you can have drastic strength differences of 7075 depending on the Temper. the yield strength for 7075 without heat treat is ~21,000 psi while T6 is ~65,000 psi. for 6061 with no heat treat the yield strength is ~8000 psi, and 6061 with T6 heat treatment is roughly 35,000 psi of yield...
how pretty do you want it? if you want it to work angle grinder, if you want pretty and have time a file or a dremel..... if you have $$ and want it pretty machine shop (end mill is the way to do it as mentioned above).
also if you have a decent cordless power drill you can totally do it as...
the reason google will route you 895 is because a lot of people are avoiding it blindly. once you get on 895 there is 1 lane. then the 97 NB traffic merges, then the traffic is merging through the toll booth. pick the right most toll booth (ez pass is lane 3 i think, lane 1 for cash) and then...
for karma i have 2 tickets to the slightly less disappointing team in the region, the Washington nationals. The game is THIS SATURDAY, August 18th at 7:05 (1905 for you 24 hour types!). The tickets are in section 222 row D. The wife and I are unable to go to the game so we are giving them away...
one can make firearms for their personal use. a 3D printer is no different than a file and a saw... or a mill and a lathe... or a CnC machine.... or home depot's plumbing section, a nail, and a shotgun shell......
i mean how many polymer semi auto's do i need? i bought a gen 5 cuz of the ambi slide stop and my wife is a southpaw. i could have bought a different handgun, but i have magazines and the such for g19 so... i have a lefthanded g19 to go with my right handed one. i may be in the minority, but i...