Recent content by Kizmit99
The #1 community for Gun Owners of the Northeast
Member Benefits:
No ad networks! Discuss all aspects of firearm ownership Discuss anti-gun legislation Buy, sell, and trade in the classified section Chat with Local gun shops, ranges, trainers & other businesses Discover free outdoor shooting areas View up to date on firearm-related events Share photos & video with other members ...and so much more!
Member Benefits:
-
K
CETME Model L (.223) in the US
I suspect there are probably more differences between the L and LC than simply the stock, because there's a fairly long spring and rod that extend a fair distance into the fixed stock. Also, the tail on the carrier extends about 3 inches past the rear of the receiver when fully back. The LC... -
K
CETME Model L (.223) in the US
I haven't run across those before -- but they look like they would probably do a decent job if you don't have access to a lathe... I've got one of Gary Clark's strikers. I have a few kits though, so my plan is to make a couple copies of his original (probably not cost-effective, but I like... -
K
CETME Model L (.223) in the US
Sorry to hear that - although I doubt that will turn out to be that big of a problem... If you have a way of knurling the barrel I doubt it will take much to get it back to a press-fit. The knurling will increase the diameter slightly and (I suspect) it will only need to be increased by a... -
K
CETME Model L (.223) in the US
Be sure to check the fit of the barrel to the trunnion. At least a few folks are finding they're cut too small for a press-fit in the trunnions they have. Others seem to be fine. I suspect that trunnion specs varied slightly (by a few thousandths) across kits. I know that my trunnion... -
K
CETME Model L (.223) in the US
Greetings all - I haven't logged on here since back in May, but it's good to see some more CETME-Ls getting built in maryland. Here's a pic of the one I did: The complete build is documented over on WeaponsGuild (if you're a member there)... -
K
Laws regarding making of regulated firearms prior to Oct. 1st
What is the current thinking on building a handgun post Oct? I would assume that the status-quo would remain and that as long as you are not prohibited from owning the firearm, you would not be prohibited from manufacturing it (assuming, of course, that this was done for personal use and with...- Kizmit99
- Post #12
- Forum: Maryland 2A Issues
-
K
Laws regarding making of regulated firearms prior to Oct. 1st
I would assume that non-semi-automatic rifles would also be gtg? For example, an AK kit, built on a receiver made from a flat, with a virgin barrel without the gas port drilled. All purchased and built after Oct 1. I assume that wouldn't be a problem, but what's the current consensus?- Kizmit99
- Post #10
- Forum: Maryland 2A Issues
-
K
Official February 6th day of event thread.
Good to hear! What I said was announced in lawyers square (or whatever this square is called) by the gentleman who's been leading the crowd in quoting the second amendment. Seemed like a reasonable source. Hope everyone in line gets signed up- keep them here all night!- Kizmit99
- Post #33
- Forum: Maryland 2A Issues
-
K
Official February 6th day of event thread.
It was just announced that they've stopped signing up additional speakers. No idea whether that's true. Supposedly still taking written testimony...- Kizmit99
- Post #22
- Forum: Maryland 2A Issues
-
K
Maryland Gun Bill Summary...
This is great, thanks! Question - do folks think it would be good-form or bad-form to send individual emails to appropriate representatives (house vs senate) for each of these bills? Basically stating position (support/oppose) on each individual bill versus the generic "support our 2nd...- Kizmit99
- Post #30
- Forum: Maryland 2A Issues
-
K
AK 47 noob question
Hope you didn't have an success with that - there should be a rivet pinning the piston to the bolt-carrier... (the ends will be ground smooth with the piston, so may not be obvious). -
K
Scope for m&p 15-22
I like the NcStar Mark III - I've got one on my 15-22 and love it. I wouldn't expect it to work well on a real AR-15, but recoil on the 15-22 is so low it doesn't have any issues holding zero... -
K
What are your plans for your WMD BCG and BHW barrel?
I'm thinking about an A2 style carbine with a slidefire stock. But the uppers I bought from the group buy earlier in the year were A3 (flat top) style. I'm not 'feeling' the detachable carry handle, so I'm probably gonna have to get a different upper for it... -
K
Bass Pro...
I was in there on Thursday evening (about 6pm), the number system wasn't in place. My wife wanted to compare field glasses. After standing around for 20 minutes, with 4 folks behind the counter and only two looking like they were actually helping customers, we left. There were several other...