Milled rcvr MAK90 question

[FFBWMD]

OK, i have a question. I recently got a milled rcvr MAK90, however i cannot stand the loophole stock. Anybody know where to get a different stock set. I know the MAK's are different on the rear of the rcvr. Thanks in advance

 

[fivepointstar]

its easy to remove the stock. you'll have to buy a pistol grip and screw and a stock for a milled receiver. takes a few minutes to install. K-var sells them

http://www.k-var.com/shop/product.php?productid=17064&cat=251&page=1

I did the same with my post ban Arsenal

 

[StantonCree]

Here are your options for the Milled Mak. You can get an Ironwood Stock set and dress it up like this:

There is a ton of info on theakforum.net. That pic is from this thread in the Chinese subsection:

http://www.theakforum.net/phpBB3/viewtopic.php?f=15&t=163983

Your other option is to make it an Underfolder. Matt (aka Turbothis from www.gunsnorthwest.com) can help you out with that.

 

[StantonCree]

its easy to remove the stock. you'll have to buy a pistol grip and screw and a stock for a milled receiver. takes a few minutes to install. K-var sells them

http://www.k-var.com/shop/product.php?productid=17064&cat=251&page=1

I did the same with my post ban Arsenal

Good info but the kvar milled stock sets will not work on Milled Mak90's - the receiver is cut differently (the milled maks have an angled cut reciever - see the pic above).

 

[rj1974]

You will also need to replace internal parts to make it 922r compliant .

http://jobson.us/922r/

 

[rj1974]

Good info but the kvar milled stock sets will not work on Milled Mak90's - the receiver is cut differently (the milled maks have an angled cut reciever - see the pic above).

Try out Iron wood stocks . They make some nice sets .

http://ironwooddesigns.com/IWDHome.html

 

[Markp]

You will also need to replace internal parts to make it 922r compliant .

http://jobson.us/922r/

Not if it was imported before 1989. At least that has been the stance of the ATF so far.

 

[fivepointstar]

Good info but the kvar milled stock sets will not work on Milled Mak90's - the receiver is cut differently (the milled maks have an angled cut reciever - see the pic above).

thanks for the tip i did not know that!

BTW your MAK is beautiful!!!!

 

[fivepointstar]

Here are your options for the Milled Mak. You can get an Ironwood Stock set and dress it up like this:

There is a ton of info on theakforum.net. That pic is from this thread in the Chinese subsection:

http://www.theakforum.net/phpBB3/viewtopic.php?f=15&t=163983

Your other option is to make it an Underfolder. Matt (aka Turbothis from www.gunsnorthwest.com) can help you out with that.

thats HOT!

 

[FFBWMD]

Good info but the kvar milled stock sets will not work on Milled Mak90's - the receiver is cut differently (the milled maks have an angled cut reciever - see the pic above).

that was my problem because of the angled rcvr

 

[rj1974]

Not if it was imported before 1989. At least that has been the stance of the ATF so far.

assumed it was after since he stated it has a thumbhole stock .

 

[StantonCree]

hahaha FPS I wish that was mine its from the thread with the info on how to dress up the milled MAK on the AKFORUM