Form 1 $100 suppressor

The #1 community for Gun Owners of the Northeast

Member Benefits:

  • No ad networks!
  • Discuss all aspects of firearm ownership
  • Discuss anti-gun legislation
  • Buy, sell, and trade in the classified section
  • Chat with Local gun shops, ranges, trainers & other businesses
  • Discover free outdoor shooting areas
  • View up to date on firearm-related events
  • Share photos & video with other members
  • ...and so much more!
  • Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    Here is a repost since the last thread was spammed and deleted.

    Reserved for parts list, cost, links & other info.

    Carbon Steel tube, Alum ends, direct thread on

    Tax stamp, $200 required.

    Break to can adapter (thread protector D-Cell), $19.99 Required. http://sdtacticalarms-com.3dcartstores.com/D-cell-Maglite-Rear-Thread-Protector-non-anodized-and-anodized_p_15.html

    8.375" Steel tube D-Cell, $30.99 required if not using a donor flashlight for a tube. http://sdtacticalarms-com.3dcartstores.com/SOLVENT-TRAP-TUBES_p_47.html

    SS D-Cell Spacer and blast tube, $10.00 required. http://sdtacticalarms-com.3dcartstores.com/Stainless-D-Aluminum-C-and-D-PVC-Pipe_p_41.html

    Freeze Plugs 381-3179, $11 for a 12 pack at Napa required. http://www.napaonline.com/Catalog/C...lug-1-350-34-300-mm/_/R-SEP3813179_0186397517

    End Cap, $19.99 Aluminum D Cell. http://sdtacticalarms-com.3dcartstores.com/End-Caps_p_50.html

    Total Estimated total for Steel tube with Aluminum ends, direct thread on build parts: $92.96 + Tax stamp $200 = $292.96 Total



    Carbon Steel Parts list

    Tax stamp, $200 required.

    Muzzle Break, $56.99 not required. You can use an adapter that threads directly to the barrel. http://sdtacticalarms-com.3dcartstores.com/SDTA-Muzzle-Break_p_65.html

    Break to can adapter (thread protector D-Cell), $34.99 Required. http://sdtacticalarms-com.3dcartstores.com/Carbon-steel-Rear-thread-protector-D-cell_p_70.html

    8.375" Steel tube D-Cell, $30.99 required if not using a donor flashlight for a tube. http://sdtacticalarms-com.3dcartstores.com/SOLVENT-TRAP-TUBES_p_47.html

    SS D-Cell Spacer and blast tube, $10.00 required. http://sdtacticalarms-com.3dcartstores.com/Stainless-D-Aluminum-C-and-D-PVC-Pipe_p_41.html

    Freeze Plugs 381-3179, $11 for a 12 pack at Napa required. http://www.napaonline.com/Catalog/C...lug-1-350-34-300-mm/_/R-SEP3813179_0186397517

    End Cap, $34.99 Carbon Steel D Cell. http://sdtacticalarms-com.3dcartstores.com/End-Caps_p_50.html

    Total Estimated total for Steel build parts: $178.96 + Tax stamp $200 = $378.96 Total



    Titanium build

    Tax stamp, $200 required.

    Muzzle Break, $56.99 not required. You can use an adapter that threads directly to the barrel. http://sdtacticalarms-com.3dcartstores.com/SDTA-Muzzle-Break_p_65.html

    Break to can adapter (thread protector D-Cell), $19.99 Required add the option to the break selection. http://sdtacticalarms-com.3dcartstores.com/SDTA-Muzzle-Break_p_65.html

    8" Titanium tube D-Cell, $69.99 required if not using a donor flashlight for a tube. http://sdtacticalarms-com.3dcartstores.com/SOLVENT-TRAP-TUBES_p_47.html

    SS D-Cell Spacer and blast tube, $10.00 required. http://sdtacticalarms-com.3dcartstores.com/Stainless-D-Aluminum-C-and-D-PVC-Pipe_p_41.html

    Freeze Plugs 381-3179, $11 for a 12 pack at Napa required.

    End Cap, $19.99 Aluminium D Cell. http://sdtacticalarms-com.3dcartstores.com/End-Caps_p_50.html

    Total Estimated total for Titanium Build parts: $187.96 + Tax stamp $200 = $397.96 Total




    Purchased tools

    Depending on the style you want to do, there are different methods. The most basic method is not angling the baffles at all. You just use the centering tool and a drill to drill the middle to the desired caliber. I will be testing non angle baffles, 45 deg angled baffles and 60 degree baffles. I may test different combinations of the baffles as well, along with different spacing arrangements.

    Center Tool $19.99, required. http://sdtacticalarms-com.3dcartstores.com/Centering-Tools_c_17.html

    Puller tip 45 degree, required if adding an angle to baffles. If you don't have a puller to use the tip off of, there are replacement tips online for $10-$15.

    60 Degree tip, required if wanting this angle on your baffles. It is recommend you start with 45 then use the 60 to prevent distorting the baffle. $11.83 http://www.amazon.com/dp/B00012YFKI/ref=sr_ph?ie=UTF8&qid=1416935804&sr=1&keywords=grizzly+mt2

    Puller tip that is close to 60 degrees. just another example of something you can use. $6.07. http://www.toolup.com/proto_j4012t_puller-tip-detachable-sta.aspx

    And then there is a complete setup, it forms perfect consistent baffles over and over again, and gives you a perfectly centered bore. The price is perfect and well worth the investment.

    http://www.jstactical.com/JForm-D-SS-Complete_p_15.html



    Baffles:

    There are two brands of baffles that I have found will fit.

    This is the one I linked to above.



    This part number is stronger and slightly longer in the depth. They also fit tighter in the tube, and require just a slight bit of pressure to push down the tube. These may create a better seal, but either will work just fine.

     
    Last edited:

    Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    Reserved for write up.

    Step 1: E-File form 1, and pay $200 tax.
    Step 2: Impatiently wait for your approved stamp... This stamp took 41 days to be approved.
    Step 2.b: Order the parts and pieces (see list above post).
    Step 3: Form Baffles. There are many methods for this, I tried most of them. My preferred method that results in the most consistent baffles was using the tool and die to form the angle.

    I was able to do this with a vice, but was pretty tough to do. It felt like any second the vice handle was about to break. Using a 6 ton hydraulic press made the job much easier.



    Place a freeze plug on to the tool.



    Then place the sleeve over the tool, and insert the die into the sleeve.





    Place the whole tool into a vice and crank it down until you can't move it anymore.



    Check the angle to make sure you depressed it enough.

    Here is a before and after photo.



    Using a press makes the job much easier, follow the same process as above but place the tool under the press instead of in the vice.





    Press the die into the tool, until it reaches max depth. I measure with my calipers the die to sleeve difference to make sure they are all pressed to the same depth.



    Remove the sleeve and the die, and inspect. Sometimes depending on the plug brand, they may be slightly stuck onto the die body. A slight tap of a hammer frees them easily.



    Your finished dented/formed baffle ready to be drilled.



    Alternative forming process

    This method is for if you don't buy the forming tool I recommend. This method you will need a centering tool (not pictured) from SDTA $20. In this example I'm using a 23mm craftsman socket, a 45deg flaring tool center bit, and the 60 deg lathe bit.

    First step in this method is to drill your starting hole with the centering tool. This gives the forming bit a spot to center off.

    C4741979-99E6-46E9-A11C-DB4D0F631D22_zpshztuk7e9.jpg


    The plug fits over the socket pretty good, but depending on brand it may be slightly loose. If so a wrap or two of tape will make it tight.

    Place the plug over the socket, and align the forming bit in the center and place in the vice. Before cranking down, make sure the everything is square.

    C09916E6-FD28-4C8A-89B2-0287954E0E3C_zpsiaipvj95.jpg


    Tighten down until the bit is touching the plug completely.

    If you are planing to use the 60 deg angle you will form the 45 deg first, then step up to the 60deg. Follow the same process as above with the 60 deg bit.

    2BEB5F33-6057-4212-8251-36DF4E829D10_zpstud9y70w.jpg


    The center hole will grow as you are forming, you want to make sure this does not get bigger than your desired final hole size. I recommend making it smaller than that size and use a drill but to give you the final size.

    Here is a socket formed baffle.

    FFF47D64-995B-48DA-85E3-1C9268983DDA_zpso144rild.jpg


    Step 4 Drilling baffle holes

    If using the baffle forming tool, you DO NOT drill prior to forming. Form the plug and then drill it. See this picture of two plugs, the plug on the left was formed and then drilled. The one on the right was drilled and then formed. The hole will grow as you form, I believe it is better to form and then drill for consistency and plug thickness.

    3E7A2B95-3F63-4524-98F0-82E665C207E2_zpsmrzwbtit.jpg


    While the tool is in the forming tool, drill your center hole.

    44D2F9C0-C41D-4219-A748-5110FD2F8DF5_zpstku370a7.jpg


    After drilling your center hole with the tool, you now just have to increase to the desired caliber size. For this 30 caliber can .371 would be the size we are looking for. A 3/8 drill bit is .375, you can either order the .371 bit or use what you have. Going slightly bigger is safer and easier, but it will decrease the effectiveness slightly.

    Here is a chart that I have created based on testing that gives the best performance for suppression, safety, and accuracy.



    I used a drill press to complete the holes. It's important to slowly step up to the final size. This prevents you from getting off center, and gives a cleaner hole.

    My centering tool uses a 3/16 bit. I slowly stepped up a bit size at a time. Using the drill press and a pair of channel locks, line the center up, the drill bit will center off the smaller size hole.

    5C099607-1D9D-4411-BEA5-0FDFAC6E2DFE_zpscd6tf2jq.jpg


    E53CBAAF-E88E-413A-A926-6F31442AA53F_zpsfqfd9nkw.jpg


    After you get to your desired size, check to make sure they are centered and if anything looks off, destroy it. Freeze plugs are cheap, blowing up your can up is not.

    Inspect the hole and clean any burrs off.

    49D3B9DA-C50C-46D7-99A9-2086FF4BA2C0_zps2hljaehx.jpg


    Step 5 End cap

    After you have all your plugs done and cleaned up, and everything looks good it's time to drill the end cap. When you buy this from SDTA it will come center marked and the hole is started.

    755A07C8-0850-4812-8758-C566914E3DBE_zpssb3tubjh.jpg


    4D032609-061E-4FAB-8F77-A26FD89D083D_zpsg0td1huf.jpg


    First step is to drill the hole they started the rest of the way. This is done just like the plugs on the drill press. Slowly step up the drill bit size until you get to your desired size. When finished you should have a nice end cap with a clean center hole.

    3C5F0412-4FDF-4352-917D-78A295662BE8_zpsq86aaxeh.jpg


    Do another inspection of all your baffles and end cap. Everything should be nice and centered, clean with no metal burrs.

    7780F44A-9487-43C9-A966-D5C6C3C183B3_zpsv6p1zecn.jpg


    Step 6 Assembly

    Someone on another forum recommends the use of the high temp o-rings to help seal the suppressor and add resistance to the ends cap. I placed one on the end cap and tightened it down. After finishing the build it was pointed out that the oring should fit inside the tube. It does not on mine. I called SDTA where my parts came from and they do not recommend using them, so I removed them from my build.

    E2E02467-892E-406A-984D-3430F1DC71B8_zpsdoch3uqa.jpg


    Next install the baffles in the configuration of your choice.

    C7D505E1-8953-410B-918D-3FAB5BF97791_zpsropfltek.jpg


    Push them down and make sure they are fully in place.

    964C1340-93B8-4101-A031-A5589E509B0F_zpsdgw4fird.jpg
     
    Last edited:

    Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    Step 7 Blast chamber spacer

    The blast chamber needs to be at least the length of your break that the adapter doesn't cover. Install the end cap onto the adapter and measure the length.



    If your internal measurement (we will do this next) is not at least this long, you will need to remove a baffle or two.

    Next measure the distance from the top of the tube, to the first baffle.

    4417B96A-06BC-420A-824E-CFF2E60735C4_zpsxspvocod.jpg


    Then measure the distance between the face of the end cap and the o-ring.



    Subtract the two measurements and that is the length of your blast chamber spacer. There are many ways to cut the spacer, just make sure you have a nice clean square cut.

    1DFF1720-5CAA-44A3-988F-D128CA1183CA_zpssmzmtpdk.jpg


    Step 8 final assembly

    Place your blast chamber spacer in the tube, and then the end cap. Tighten it down and make sure everything is tight and compacted inside.



    Make sure there is no movement of the internal parts, and you can see through the can with no obstructions. If you have a bore rod, stick it in to check the alignment.

    7701AC6D-9A68-4814-9DC8-8102F3D3D0A7_zpsqubivhpq.jpg


    Step 9 coating

    You can finish your can with what ever you choose. I'm using high temp header paint. I have already coated the can prior to assembly, following the instructions on the paint can.



    Step 10 Engraving

    Your Form 1 suppressor needs to be properly marked per the ATF. Some guys do their own since it doesn't cost anything. You can engrave it or stamp it, but it needs to be .003 deep. You should have the trust name, city and state, model, serial, and caliber all as they appear on your paperwork for the approved stamp.



    Since I have a titanium tube, and I'm not very good at engraving I decided to have mine done by a professional. A local jewelry shop quoted me $50, online places are $35-$50 plus shipping. Follow all laws on proper placement, script type, etc.
     
    Last edited:

    Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    E-File a Form 1 Suppressor:

    Start by going to http://www.atfonline.gov



    Create your account and login.

    Once inside, scroll over to Form 1 and click it.



    Down at the bottom click "Next"



    On this screen you select Tax paid ($200), and if you want you add an internal control number. This is not required, and is useful if you are submitting multiple stamps. I use #1 for my first stamp, #2 for my second, #3 for my third, etc...



    Next we select No FFL.

    Enter the Trust Name under Licensee.

    Country, United States.

    Your address (typically)

    Phone and email.

    And then click next.



    Select By Manufacture code, and for Form 1 suppressors enter FMI as the code.

    Then Click Verify Manufacture, and you should get a pop up that says successful.

    Select United States and click Next.



    Next we enter the information for the NFA item.

    Start by selecting Add Firearm.



    Select the Silencer from the drop down.

    Enter the model, selecting one on the list will decrease the wait time, but you may enter what ever you want.

    Select the caliber, and the unit of measure.

    Then add why you intend to make this item. I always use "All Legal Purposes" some guys like to have fun with this field.

    Then click next.



    The next screen we do not use, this is used for other items where plans are required. Just click Finish.



    Now you should see your item on the screen, click next.



    Here is where we add our trust to the Form 1.

    Click choose file, and select your file. It needs to be smaller than 3MB.

    The select trust as the document type, and enter a description.

    Once you click "add" you should see your file.

    Then select next.



    Your status should show that your application has been validated successfully, and you now check the box and click the payment screen.



    If you selected a model and caliber combination that was not listed and you selected the "My item description is not in the list, create new item", you will see the alert message in the picture below. This is not a problem, but the ATF will need to validate your model and caliber selections prior to changing your status to submitted/processing. This may add a few days to your wait time, but is not an issue. Continue as normal.



    Follow the process for the payment, pay with a credit card.


    If everything went through properly you should see this screen.



    It will bring you back to this screen and you can now select Sign & Submit.

    It will ask you to enter your username and password to electronically sign the document.

    And you are done.

    You should now see the "submitted/in process" under my forms, which you can select and then see Form 1 under it. Click Form 1 and it will bring up your application that is in process. If not, it may be pending for validation due to your model and caliber combination.
     
    Last edited:

    gre24ene

    Ultimate Member
    Mar 6, 2012
    1,519
    I submitted a Form1 after reading WEBER's thread here and also several other threads on the web.
     

    Xshot

    Ultimate Member
    BANNED!!!
    Aug 14, 2013
    1,645
    Pasadena, MD
    Also, how do you cut the titanium tube?

    The titanium tubes listed on the site don't come in 8". The site says "the new titanium tubes come in sizes X Y and Z". Would it be any different using the 7.6" tube?
     

    Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    Also, how do you cut the titanium tube?

    The titanium tubes listed on the site don't come in 8". The site says "the new titanium tubes come in sizes X Y and Z". Would it be any different using the 7.6" tube?

    The spacer material?

    You can cut it with a good pipe cutter, sawzall, cutoff wheel...
     

    Xshot

    Ultimate Member
    BANNED!!!
    Aug 14, 2013
    1,645
    Pasadena, MD
    The spacer material?



    You can cut it with a good pipe cutter, sawzall, cutoff wheel...


    Wasn't sure regular tools would actually cut it.

    About the change in length, the new titanium pipe is 7.6" instead of 8". How does that affect the number of freeze plugs? Will it be one less or would there be a spacer needed to make up that 0.4"?
    Does that make sense?
     

    md_al

    Active Member
    Apr 25, 2014
    724
    Middle River
    What is the minimum length of the D cell tube for an AR Pistol with 11.5 inch barrel? Would the 5.8 inch tube do or does it have to be the 7.6 inch length?

    If not considering weight would all freeze plugs do a better job in suppressing noise compared to using spacers?



    PS. Thank you for resurrecting this thread!
     

    Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    Wasn't sure regular tools would actually cut it.

    About the change in length, the new titanium pipe is 7.6" instead of 8". How does that affect the number of freeze plugs? Will it be one less or would there be a spacer needed to make up that 0.4"?
    Does that make sense?

    The tubes have always been in .6 measurements, are normally round up when talking about them.

    The tubes also have a slight variance between them, none on my tubes are exactly the same. When you add the end caps it gets you close to 8" since each one is close to .25".
     

    Weber

    USMC
    Oct 12, 2009
    1,329
    Elkton, MD
    What is the minimum length of the D cell tube for an AR Pistol with 11.5 inch barrel? Would the 5.8 inch tube do or does it have to be the 7.6 inch length?

    If not considering weight would all freeze plugs do a better job in suppressing noise compared to using spacers?



    PS. Thank you for resurrecting this thread!

    Depends on the caliber.

    I have a 5.6" on a blackout, and a 7.6" & a 9.6 on a 556. 556 short barrels are hard to suppress, but you can really take them down. I have the 9.6" on a 7" barrel and a 7.6" on a 10", but with great success. The blackout is incredible with subs.
     

    md_al

    Active Member
    Apr 25, 2014
    724
    Middle River
    Depends on the caliber.

    I have a 5.6" on a blackout, and a 7.6" & a 9.6 on a 556. 556 short barrels are hard to suppress, but you can really take them down. I have the 9.6" on a 7" barrel and a 7.6" on a 10", but with great success. The blackout is incredible with subs.

    I just wanted to know if the 5.8" D cell Titanium tube that I am using on my Glock 17 can be used on an 11.5" AR pistol. It is bored for 45 cal.
     

    Users who are viewing this thread

    Latest posts

    Forum statistics

    Threads
    274,919
    Messages
    7,258,773
    Members
    33,348
    Latest member
    Eric_Hehl

    Latest threads

    Top Bottom