10-22 takedown 1st range trip

steveh326 · Apr 19, 2015

10-22 takedown - epic fun
Volquartsen trigger guts - epic success
Leupold QR scope rings - epic FAIL

Love everything about this gun except after I sighted in at 25 yards, then tested scope removal/reinstall, scope was off by 3" at 25 yards.

Love the Nikon rimfire scope but it won't fit in the bag installed on the receiver. I need to either replace the scope with a bugbuster or replace the bag with something that will let me use conventional fixed scope mounts.

anyone familiar with these roll and go cases?

http://www.roll-n-go.net/shop/1022-case

smg1231 · Apr 19, 2015

Nice! Got to love the 10/22 takedown!

Here is a case that allows a small scope:
http://www.crusadergearllc.com/10-22-take-down-bag/

Ifdot · Apr 19, 2015

I run the Nikon P-22 on mine with UTG quick release scope rings and have no POI change with removal. You sure everything is set up properly? Do you have your barrel tight? I had to tighten mine out of the box when I got it. It seemed to lock up fine but I got to messing with it and was able to get it a good 1/4 turn tighter and still with in what ruger calls for in the specs.

I like that roll and go case though!

These are the rings.
http://www.amazon.com/UTG-Strength-...d=1429489063&sr=1-3&keywords=utg+scope+mounts

steveh326 · Apr 19, 2015

Ifdot said:
I run the Nikon P-22 on mine with UTG quick release scope rings and have no POI change with removal. You sure everything is set up properly? Do you have your barrel tight? I had to tighten mine out of the box when I got it. It seemed to lock up fine but I got to messing with it and was able to get it a good 1/4 turn tighter and still with in what ruger calls for in the specs.

I like that roll and go case though!

These are the rings.
http://www.amazon.com/UTG-Strength-...d=1429489063&sr=1-3&keywords=utg+scope+mounts

Thanks ! I thought it was tight but I'll double check it. All I did tho was take the scope off and put it back on, I did not break the rifle down for that test, and it put 50-80 rounds in a nice tight group prior to that.

Kagetsu · Apr 19, 2015

I need a scope for mine and I'm looking for tight and compact. I'm looking at the Weaver RV-7 Rimfire Classic. I'm not sold on quick release but the little ones like above look promising.

Hollywood Ball · May 17, 2015

steveh326 said:
10-22 takedown - epic fun
Volquartsen trigger guts - epic success
Leupold QR scope rings - epic FAIL

Love everything about this gun except after I sighted in at 25 yards, then tested scope removal/reinstall, scope was off by 3" at 25 yards.

Love the Nikon rimfire scope but it won't fit in the bag installed on the receiver. I need to either replace the scope with a bugbuster or replace the bag with something that will let me use conventional fixed scope mounts.

anyone familiar with these roll and go cases?

http://www.roll-n-go.net/shop/1022-case

Did you try fitting it in the case, but not in the pouch inside the case?

I just added a Bushnell rimfire scope to mine ($30 at Walmart). It came with rings, but they were garbage. Grabbed a set of Leupold rings and its set up pretty nice. No range report yet. So we'll see how it holds zero.

The receiver no longer fits in the big pouch on one side, but it does still fit in the bag outside of the pouch.

Mini14tac · May 18, 2015

Leupold QR scope rings - epic FAIL

Love everything about this gun except after I sighted in at 25 yards, then tested scope removal/reinstall, scope was off by 3" at 25 yards.

Interesting on the QR rings. I have them on my non takedown 10/22 with a Redfield Tac22 installed and after removing and reinstalling the scope mine is dead on @ 50yards. Did you install in the same slots and push the scope forward and down while tightening the rings?

Speed3 · May 18, 2015

My 2-7 leupold scope fits in the bag...I didn't do QD rings to avoid the issues you guys are talking about

ducrider45 · May 28, 2015

I use the QR rings on all of my 10/22's. I have never had any set not keep its zero when removed and reinstalled.

pop-gunner · May 28, 2015

I used QR on mine and never had trouble retaining zero.

Clem · May 28, 2015

I use Warne QD mounts on a number of my rifles, including my 10/22 TD. They seem to hold zero pretty well, at least as near as I can tell. The Ruger case seems to have a nice little pocket for the scope after it is removed. I haven't looked at the case lately, but that is how I remember it.

10-22 takedown 1st range trip

The #1 community for Gun Owners of the Northeast

Member Benefits:

steveh326

Ultimate Member

smg1231

Member

Ifdot

Ultimate Member

steveh326

Ultimate Member

Kagetsu

Active Member

Hollywood Ball

Mountaineer

Mini14tac

Ultimate Member

Speed3

Ultimate Member

ducrider45

Active Member

pop-gunner

Ultimate Member

Clem

Member

Users who are viewing this thread

Latest posts

Forum statistics

Latest threads

Forum statistics

Share this page